Gas
Moderators: Chem_Mod, Chem_Admin
-
- Posts: 157
- Joined: Wed Sep 30, 2020 9:34 pm
-
- Posts: 102
- Joined: Wed Sep 30, 2020 9:35 pm
- Been upvoted: 4 times
Re: Gas
I think you would be given the units of the pressure of a gas. If they ask for a different unit in the answer, then you could just convert between the units, but bar and atm are very similar in value so there is not much difference between their values.
-
- Posts: 153
- Joined: Wed Sep 30, 2020 9:39 pm
Re: Gas
The question should always specify the units, since the gas constant we use is dependent on the units of the problem. Furthermore, it would only matter when choosing the gas constant because bar and atm are essentially equivalent.
-
- Posts: 51
- Joined: Wed Nov 18, 2020 12:26 am
- Been upvoted: 1 time
Re: Gas
1 bar = .9869 atm. The problem should always give you units and if you need you can convert between units with that ratio.
-
- Posts: 105
- Joined: Wed Sep 30, 2020 10:03 pm
- Been upvoted: 2 times
Re: Gas
In one of the lecture, Lavelle said that for purposes of this class we can use atm and bar interchangeably. So even though they technically aren't equal, for this course we can assume 1atm=1bar
-
- Posts: 106
- Joined: Wed Sep 30, 2020 9:35 pm
Re: Gas
We should be given the units in whatever question we have, but 1 bar is roughly equal to 1 atmosphere so we use them interchangeably
-
- Posts: 96
- Joined: Wed Sep 30, 2020 10:09 pm
Re: Gas
The question will usually give you which unit to use but since 1 bar is roughly equal to 1 atm, we can use them interchangeably.
-
- Posts: 108
- Joined: Wed Sep 30, 2020 9:51 pm
Re: Gas
I think we'd be asked to give it in either bar or atm, but in one of the lecture videos he said that 1 bar is approximately 1 atm, so I guess its just up to whether the problem is asking for bar or atm in units.
-
- Posts: 116
- Joined: Wed Sep 30, 2020 9:39 pm
Re: Gas
I think the question would specify the units. Lavelle also mentioned that we can use them interchangeably in this class because they are approximately equal.
-
- Posts: 103
- Joined: Wed Sep 30, 2020 9:34 pm
Re: Gas
Gases for the partial pressure use atm and bars interchangeably (since they are basically the same value/ a lot like Watts and Joules if that makes any sense). It's just that our books use bars rather than atm. more often.
-
- Posts: 102
- Joined: Wed Sep 30, 2020 9:41 pm
- Been upvoted: 1 time
Re: Gas
The question should mention the units that are being used whether it be bar or atm, but Dr.Lavelle did mention that for this class we would be using atm and bar interchangeably although they are not necessarily equal.
-
- Posts: 108
- Joined: Wed Sep 30, 2020 9:36 pm
- Been upvoted: 1 time
Re: Gas
Typically, the units of the gas will be given in the equation. Bar is the SI unit for gas, so if it does not say a unit, it may be safe to assume that the gas is measured in bar. However, atm and bar are so close that the professor said we can typically trade them out without consequence.
-
- Posts: 100
- Joined: Wed Sep 30, 2020 9:51 pm
Re: Gas
The units would usually be given, but they can be interchanged in this class because they are similar.
-
- Posts: 102
- Joined: Wed Sep 30, 2020 9:37 pm
Re: Gas
Although bar is technically the correct unit to use for pressure in equilibrium equations, we use bar and atm interchangeably in this class. Dr. Lavelle said that we will usually use atm, but a problem might give you bar instead.
-
- Posts: 101
- Joined: Wed Sep 30, 2020 10:02 pm
- Been upvoted: 3 times
Re: Gas
You'll probably get the units from the question and if not, you can just convert to the correct one at the end of the question.
Return to “Applying Le Chatelier's Principle to Changes in Chemical & Physical Conditions”
Who is online
Users browsing this forum: No registered users and 9 guests